|
Standards for PE pressure piping systems
|
| |
|
| ISO 4427-1 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 1: General |
| ISO 4427-2 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 2: Pipes |
| ISO 4427-3 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 3: Fittings |
| ISO 4427-5 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 5: Fitness for purpose of the system |
| ISO 4437-1 |
Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 1: General |
| ISO 4437-2 |
Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 2: Pipes |
| ISO 4437-3 |
Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 3: Fittings |
| ISO 4437-4 |
Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 4: Valves |
| ISO 4437-5 |
Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 5: Fitness for purpose of the system |
| EN 1555-1 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 1: General |
| EN 1555-2 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 2: Pipes |
| EN 1555-3 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 3: Fittings |
| EN 1555-4 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 4: Valves |
| EN 1555-5 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 5: Fitness for purpose of the system |
| CEN/TS 1555-7 |
Plastics piping systems for the supply of gaseous fuels –Polyethylene (PE) – Part 7: Guidance for assessment of conformity |
| EN 12201-1 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 1: General |
| EN 12201-2 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 2: Pipes |
| EN 12201-3 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 3: Fittings |
| EN 12201-4 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 4: Valves |
| EN 12201-5 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 5: Fitness for purpose of the system |
| CEN/TS 12201-7 |
Plastics piping systems for water supply, and for drainage and sewerage under pressure – Polyethylene (PE) – Part 7: Guidance for assessment of conformity |
| ISO 9623 |
PE/metal and PP/metal adapter fittings for pipes for fluids under pressure – Design lengths and size of threads – Metric series |
| ISO 9624 |
Thermoplastics piping systems for fluids under pressure – Flange adapters and loose backing flanges – Mating dimensions |
| ISO 15494 |
Plastics piping systems for industrial applications – Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) – Metric series for specifications for components and the system |
| ISO 17885 |
Plastics piping systems – Mechanical fittings for pressure piping systems – Specifications |
| |
|
| Standards for jointing and installation of PE piping systems |
| ISO 12176-1 |
Plastics pipes and fittings – Equipment for fusion jointing polyethylene systems – Part 1: Butt fusion |
| ISO 12176-2 |
Plastics pipes and fittings – Equipment for fusion jointing polyethylene systems – Part 2: Electrofusion |
| ISO 12176-3 |
Plastics pipes and fittings – Equipment for fusion jointing polyethylene systems – Part 3: Operator's badge |
| ISO 12176-4 |
Plastics pipes and fittings – Equipment for fusion jointing polyethylene systems – Part 4: Traceability coding |
| ISO 13761 |
Plastics pipes and fittings – Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20°C |
| ISO 13950 |
Plastics pipes and fittings – Automatic recognition systems for electrofusion joints |
| ISO 21307 |
Plastics pipes and fittings – Butt fusion jointing procedures for polyethylene (PE) piping systems |
| ISO/TS 10839 |
Polyethylene pipes and fittings for the supply of gaseous fuels – Code of practice for design, handling and installation |
| EN 12007-2 |
Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar – Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| |
|
| Test standards for PE piping systems |
| ISO 1133-1 |
Plastics – Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics – Part 1: Standard method |
| ISO 1167-1 |
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 1: General method |
| ISO 1167-2 |
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 2: Preparation of pipe test pieces |
| ISO 1167-3 |
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 3: Preparation of components |
| ISO 1167-4 |
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 4: Preparation of assemblies |
| ISO 1183-1 |
Plastics – Methods for determining the density of non-cellular plastics – Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2 |
Plastics – Methods for determining the density of non-cellular plastics – Part 2: Density gradient column method |
| ISO 2505 |
Thermoplastics pipes – Longitudinal reversion – Test method and parameters |
| ISO 3126 |
Plastics piping systems – Plastics components – Determination of dimensions |
| ISO 4433-1 |
Thermoplastics pipes – Resistance to liquid chemicals – Classification – Part 1: Immersion test method |
| ISO 4433-2 |
Thermoplastics pipes – Resistance to liquid chemicals – Classification – Part 2: Polyolefin pipes |
| ISO 6259-1 |
Thermoplastics pipes – Determination of tensile properties – Part 1: General test method |
| ISO 6259-3 |
Thermoplastics pipes – Determination of tensile properties – Part 3: Polyolefin pipes |
| ISO 6964 |
Polyolefin pipes and fittings – Determination of carbon black content by calcination and pyrolysis – Test method |
| ISO 9080 |
Plastics piping and ducting systems – Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 9969 |
Thermoplastics pipes – Determination of ring stiffness |
| ISO 11357-6 |
Plastics – Differential scanning calorimetry (DSC) – Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 11413 |
Plastics pipes and fittings – Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| ISO 11414 |
Plastics pipes and fittings – Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 12162 |
Thermoplastics materials for pipes and fittings for pressure applications – Classification, designation and design coefficient |
| |
|
| ISO 13477 |
Thermoplastics pipes for the conveyance of fluids – Determination of resistance to rapid crack propagation (RCP) – Small-scale steady-state test (S4 test) |
| ISO 13478 |
Thermoplastics pipes for the conveyance of fluids – Determination of resistance to rapid crack propagation (RCP) – Full-scale test (FST) |
| ISO 13479 |
Polyolefin pipes for the conveyance of fluids – Determination of resistance to crack propagation – Test method for slow crack growth on notched pipes |
| ISO 13480 |
Polyethylene pipes – Resistance to slow crack growth – Cone test method |
| ISO 13951 |
Plastics piping systems – Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| ISO 13953 |
Polyethylene (PE) pipes and fittings – Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 13954 |
Plastics pipes and fittings – Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 13955 |
Plastics pipes and fittings – Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| ISO 13956 |
Plastics pipes and fittings – Decohesion test of polyethylene (PE) saddle fusion joints – Evaluation of ductility of fusion joint interface by tear test |
| ISO 13957 |
Plastics pipes and fittings – Polyethylene (PE) tapping tees – Test method for impact resistance |
| ISO 13968 |
Plastics piping and ducting systems – Thermoplastics pipes – Determination of ring flexibility |
| ISO 15512 |
Plastics – Determination of water content |
| ISO 16871 |
Plastics piping and ducting systems – Plastics pipes and fittings – Method for exposure to direct (natural) weathering |
| ISO 17778 |
Plastics piping systems – Fittings, valves and ancillaries – Determination of gaseous flow rate/pressure drop relationships |
| ISO 18553 |
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| ISO 21751 |
Plastics pipes and fittings – Decohesion test of electrofusion assemblies – Strip-bend test |
| EN 12099 |
Plastics piping systems – Polyethylene piping materials and components – Determination of volatile content |
| EN 12106 |
Plastics piping systems – Polyethylene (PE) pipes – Test method for the resistance to internal pressure after application of squeeze-off |
| |
|
| Other useful reference standards for PE |
| ISO 3 |
Preferred numbers – Series of preferred numbers |
| ISO 472 |
Plastics – Vocabulary |
| ISO 1043-1 |
Plastics – Symbols and abbreviated terms – Part 1: Basic polymers and their special characteristics |
| ISO 4065 |
Thermoplastics pipes – Universal wall thickness table |
| ISO 11922-1 |
Thermoplastics pipes for the conveyance of fluids – Dimensions and tolerances – Part 1: Metric series |
| ISO 14040 |
Environmental management – Life cycle assessment – Principles and framework |
| ISO/TR 10358 |
Plastics pipes and fittings – Combined chemical resistance classification table |
